Crusher Bushing Alloy Selection

Crusher Bushing Alloy Selection

High-Performance Self-Lubricating Bronze Bushing Solutions & Technologies. Minimize downtime, extend service life, and reduce costs for dynamic applications.

BUSHING-CRUSHER STONES

Crusher Bushing Alloy Selection

A position-by-position matrix for copper alloy bushings in spring cone and gyratory crushers.
Alloy data referenced to ASTM, SAE, EN and GB designations. Engineering guidance only — final selection must be confirmed against measured duty.

1  The governing principle

Selection principle

Bronze alloy selection in crushing equipment is decided by relative sliding speed — not by load. Load determines how much compressive strength you need. Sliding speed determines whether that strength is usable, or whether it becomes a liability.

Every crusher bushing position falls into one of two mechanical regimes, and the two require opposite material strategies.

Regime Dominant mechanism Material family Why
Low sliding speed,
high compression
Bore crushing, permanent deformation under load Aluminium bronze
C95400 / C95500 / C95800
Manganese bronze C86300
Almost no sliding means almost no frictional heat generation. Yield strength becomes the decisive property, and the poor embeddability of the harder alloys becomes irrelevant.
Rotating or rapidly
oscillating
PV heating, seizure, shaft scoring Leaded tin bronze
C93200 / C93700 / C93800
Lead supplies boundary lubrication when the oil film ruptures, and the soft matrix embeds abrasive particles instead of letting them cut the shaft journal.

Warning

Consequence for specification

A hardness rule ofthumb used on all crusher positions will produce the wrong answer on at least one of them. Selecting by hardness alone is selecting incorrectly. Determine the sliding speed at the position first, then select the alloy family.

2  Position × alloy matrix

Matrix legend
●︎  Commonly specified  — code CS
◐︎  Applicable with qualification  — code AQ
○︎  Not normally applicable  — code NA
Plain-text form, for quotation or specification documents:
CS = commonly specified  |  AQ = applicable with qualification  |  NA = not normally applicable
Position Duty signature C93700
C93800
C93200 C90300
C90700
C95400
C95500
C95800 C86300 Solid
lubricant
Eccentric bushing /
eccentric sleeve
Very high pressure, moderate to high speed, forced oil, shock from tramp material ●︎ ●︎ ○︎ ◐︎ ◐︎ ○︎ ○︎
Countershaft bush Highest rotational speed in the machine, moderate pressure, forced oil ◐︎ ●︎ ○︎ ◐︎ ○︎ ○︎ ○︎
Socket liner /
spherical bearing liner
Very high axial load, slow gyration, hydrodynamic oil film, steel mating ball ●︎ ◐︎ ○︎ ○︎ ○︎ ○︎ ◐︎
Bottom shell bush /
frame bushing
High pressure, low speed, forced oil, carries full eccentric assembly ◐︎ ●︎ ○︎ ●︎ ◐︎ ●︎ ○︎
Spider bushing Moderate pressure, oscillating, dusty, grease lubricated ●︎ ●︎ ○︎ ○︎ ○︎ ○︎ ●︎
Head bush,
upper and lower
Very high pressure, reversing, forced oil ●︎ ●︎ ○︎ ○︎ ○︎ ○︎ ○︎
Piston wearing plate /
hydroset bushing
Very high compression, very low speed, rotating against stationary piston ◐︎ ○︎ ○︎ ●︎ ●︎ ○︎ ◐︎
Thrust bearing /
step plate
Axial compression, very low speed ◐︎ ○︎ ◐︎ ●︎ ●︎ ◐︎ ◐︎
Jaw crusher
eccentric shaft bush
High cyclic pressure, moderate speed, shock load ●︎ ●︎ ○︎ ○︎ ○︎ ○︎ ○︎
Toggle seat /
toggle plate bearing
Very high pressure, oscillating, grease lubricated ○︎ ○︎ ◐︎ ●︎ ◐︎ ○︎ ●︎
Adjustment cylinder pin /
pivot flange bush
Static to intermittent, grease, dusty, frequent maintenance access ●︎ ●︎ ○︎ ●︎ ○︎ ○︎ ●︎
Curtain / apron pivot bush,
breaker plate pin
Static to intermittent, grease, dusty, high shock on tramp material ●︎ ●︎ ○︎ ●︎ ○︎ ○︎ ●︎

2.1  How to read the matrix

Read across a row to see which alloy families suit a position; read down a column to see where one alloy family belongs. The pattern is not random. Radial positions on a rotating or precessing journal fall to the leaded bronzes, because embeddability and film-breakdown tolerance dominate. Compression-dominated positions with negligible sliding fall to the aluminium and manganese bronzes, because compressive capability dominates and there is very little sliding to generate heat.

Source basis: cncrusher.net large bronze bearing grade table; CSP Mühendislik spherical bearing and socket liner maintenance guide; Yile Machinery heavy industry plain bearing selection guide; Atlas Bronze shafting and journal material guidance.

3  Integrated selection recommendation

Duty profile Recommended grade Selection logic
Slow-moving thrust or compression position, low frequency, oil supply reliable ●︎ C95400 / C95500 Compressive yield strength governs. The absence of significant sliding removes the main disadvantage of the harder alloys.
Rotating or oscillating journal, continuous forced oil, moderate load ●︎ C93200 (SAE 660) General-purpose bearing bronze. Good castability, good machinability, balanced wear resistance and thermal conductivity.
High-speed or rapidly oscillating, oil film intermittently broken, dusty environment ●︎ C93700 / C93800 Lead provides emergency boundary lubrication when the film ruptures, and embeds abrasive particles instead of transmitting them to the shaft.
Repetitive load cycles with abrasive wear, impact on tramp material ●︎ C90700 / C90300 Phosphorus refines grain structure and raises fatigue resistance under millions of load reversals.
Lubrication unreliable, intermittent service, inaccessible positions, high ambient temperature ●︎ Aluminium bronze matrix with solid lubricant inserts The matrix carries load; the embedded solid lubricant forms a transfer film. Note that solid lubricant occupies roughly 25–30 % of the bearing surface, so effective bearing area and load capacity must be recalculated accordingly.
Extreme structural load, low speed, older or specialised crusher designs ●︎ C86300 manganese bronze Highest strength of the cast bronze family. Selected where structural integrity under load outweighs machinability.
Seawater, brine, or continuous chloride exposure at a rotating position ●︎ C95800 The one regime where the nickel content earns its cost. Note that this is a marine duty condition — see section 5 before paying the premium.

4  Shaft hardness: the requirement depends on alloy condition

Aluminium bronze contains no lead. It therefore has none of the anti-seizing reserve of a leaded bearing bronze, and substantially less conformability and embeddability. This makes the mating shaft a design variable rather than a detail. The requirement is stated in two tiers, and the correct tier depends on the hardness of the alloy itself.

Aluminium bronze condition Recommended mating shaft Typical application
As cast, hardness about 140–170 HB ≥ 400 HB min C95800, C95500 and C95400 in as-cast condition. Most crusher main shaft journals, case or induction hardened, satisfy this.
Heat treated, hardness about 180–240 HB > 500 HB, or HRC 60 min Solution-treated and aged alloys, and manganese bronzes. Confirm the journal can achieve this before specifying a hardened condition.

Warning

Do not substitute one bronze for another in isolation

Replacing a leaded tin bronze bushing with an aluminium bronze while leaving every other component unchanged is a frequent cause of early failure. The harder bushing transfers more wear to the mating surface. If the existing shaft journal is not hardened to the tier required by the selected alloy, the substitution accelerates damage to a component that is far more expensive than the bushing. Verify journal hardness, surface finish and lubrication supply before changing alloy family.

Source: Copper Development Association bearing guidance; Atlas Bronze shafting and journal material selection. For reference, crusher main shaft journals are commonly specified at HRC 50–56 in industry practice. Note that ASTM E140 hardness conversion tables are derived from non-austenitic steels and do not apply to copper alloys — a Brinell value for a bronze part should be read against the standard that specifies the test load.

5  Three specification traps that recur in crusher procurement

5.1  Listing multiple grades as equivalent alternatives

A requirement written as “BS 1400 AB2, ASTM C95800, JIS CAC703 or equivalent” is not a permissive specification. It is an unresolved conflict, because the composition ranges do not coincide.

Element BS 1400 AB2 ASTM C95800 JIS CAC703C Common range Issue
Al 8.8–10.0 8.5–9.5 8.5–10.5 8.8–9.5 Narrow
Fe 4.0–5.5 3.5–4.5 3.0–6.0 4.0–4.5 ≠︎ Narrowest — 0.5 wide
Ni 4.0–5.5 4.0–5.0 3.0–6.0 4.0–5.0 Workable
Mn ≤ 3.0 0.8–1.5 0.1–1.5 0.8–1.5 ≠︎ AB2 permits far more
Pb ≤ 0.05 ≤ 0.03 ≤ 0.1 ≤ 0.03 Workable
Additional — Fe ≤ Ni — Fe ≤ Ni ≠︎ Not required by AB2

Manganese is the decisive conflict: material certified as AB2-conforming may carry up to 3 % manganese and will be rejected under C95800, which caps the element at 1.5 %. The Fe ≤ Ni constraint in C95800 is a further rejection point that AB2 does not impose, so an AB2 certificate does not demonstrate C95800 conformance, and a C95800 certificate does not demonstrate AB2 conformance.

Mechanical minimums also differ, and the lower bound belongs to the UNS grade:

Specification Tensile (MPa) 0.2 % proof (MPa) Elongation (%) Hardness (HB) HB test load
BS 1400 AB2, continuously cast, min 640 250 13 — not stated
EN 1982 CC333G, GC / GZ, min 650 280 13 ≥ 150 not stated
ASTM B148 C95800, sand cast, min 585 240 15 ≥ 159 3000 kgf

Recommendation

Recommended practice

Specify one governing standard, one casting method, one casting condition and one test-load basis for hardness. Where several designations must be permitted, attach the composition table above as an acceptance annex and state that the common range governs.

An intersection does exist and is commercially workable. For the grades above it is:
Cu ≥ 79.0 | Al 8.8–9.5 | Fe 4.0–4.5 | Ni 4.0–5.0 | Mn 0.8–1.5 | Pb ≤ 0.03 | Fe ≤ Ni

5.2  Brinell hardness without a stated test load

Lead content changes the appropriate Brinell test load for copper alloys. Leaded tin bronzes are normally evaluated at 500 kgf; aluminium and manganese bronzes at 3000 kgf. Two valid readings taken under different loads are not comparable, and a specification quoting a single hardness figure without the load cannot be verified. Always state the test load alongside the value.

5.3  Supplier grade tables that omit the alloying elements

Some published alloy tables list only the copper balance and residual impurity limits, without aluminium, iron, nickel or manganese. For an aluminium bronze these four elements are the alloy. A table that omits them imposes no technical requirement at all, and should not be used as a purchase basis. Verify against the ASTM, EN, BS or JIS document itself rather than a distributor page, and note that alloy tables for one grade sometimes differ between pages of the same source.

6  Paying for properties the duty does not require

C95800 nickel aluminium bronze is specified predominantly for seawater service. Its resistance to chloride corrosion, cavitation erosion and biofouling is the reason it carries a nickel premium. A crusher operating on aggregate, ore or quarried stone has no seawater duty, and in that environment the corrosion advantage is not exercised.

Where corrosion is not a specified requirement, C95400 aluminium bronze provides comparable compressive capability without the nickel content. Where the position is stationary relative to the shaft, the premium is entirely unnecessary. Comparing both grades against the same duty is a straightforward way to avoid paying twice for the same performance.

A second, opposite case is worth stating plainly. If the duty involves intermittent lubrication, abrasive dust, or a stated preference for the bushing to be sacrificed rather than the shaft journal, a high-leaded tin bronze is the correct answer and an aluminium bronze will score the journal. Aluminium bronze is harder and will therefore last longer in the wear test while causing more damage to the part it is protecting. Service life of the bushing alone is not the correct objective.

7  Geometry-based checks before quoting a drawing

Before a crusher bushing is treated as a standard catalogue item, four geometric checks resolve most ambiguities.

  1. Is the sliding speed physically possible? Peripheral speed follows from bore diameter and rpm. Large-diameter bushings leave the usable PV envelope for copper alloys at comparatively low rpm. If the computed PV exceeds the material limit by an order of magnitude, the duty description or the dimension is wrong — changing alloy will not resolve it.
  2. Is the spherical face present? A socket liner is a spherical plain bearing running against a hardened steel ball, with a hydrodynamic oil film. A plain cylindrical bore with no spherical radius cannot serve that function. Check for the spherical radius and for oil grooves or pockets, not just the bore diameter.
  3. Is there a register or flange? Positions carrying full axial load normally require a flange to locate the part and pins or a backing plate to retain it. A plain sleeve of uniform wall section indicates a different function.
  4. On split housings, how are the halves located? A split joint without a register or locating pins permits relative radial movement of the two halves at runtime. This fretting at the parting line is a recognised early failure mode for large split bronze bushings, and the locating feature should be defined on the drawing.

8  Alloy reference data

Alloy Designation Density
g/cm³
Tensile
MPa
Hardness
HB
Machinability
%
Leaded tin bronze C93700 / SAE 64
CuSn10Pb10
8.86–8.95 220–260 60–80 80
High-lead tin bronze C93800
CuSn7Pb13
9.25 205 min 55–65 80
Bearing bronze C93200 / SAE 660 8.8–8.9 240 min 60–70 70
Phosphor bronze C90700 8.8–8.9 approx. 300 80–110 20–40
Aluminium bronze C95400
CuAl10Fe3
7.58 585 min 170–210 60
Nickel aluminium bronze C95500 7.64 620 min 190–230 50
Nickel aluminium bronze C95800
AB2 / CAC703
7.64 585 min ≥ 159 50
Manganese bronze C86300
CuZn25Al6Fe3Mn3
8.3 approx. 760 approx. 225 20

Machinability referenced to free-cutting brass C36000 = 100 %. Hardness test load differs by alloy family — see section 5.2. Values are typical published figures for as-cast condition; the governing ASTM or EN document for the purchased grade always takes precedence. Permissible pressure and PV limits are not specified in SAE J461 or J462, which cover test method and acceptance criteria only — request a duty-specific verification from the supplier rather than relying on a catalogue figure.

9  Information required for a firm quotation

  1. Position of the part in the machine, and crusher make, model and size
  2. Rotational speed or sliding speed
  3. Radial and axial load
  4. Lubrication method and how reliable the supply is
  5. Mating shaft material, journal hardness and surface finish
  6. Working temperature and medium — dry, wet, slurry, or corrosive
  7. Supply condition — as cast, stress relieved, or heat treated
  8. Quantity per order and annual requirement
  9. Drawing with tolerances, fitting and any oil groove or drilling requirement
  10. Governing material standard and required certification level

Material certificates for copper alloy parts should reference the specific heat poured, state the casting method, and list measured chemistry rather than repeating a nominal alloy table. Test load, casting standard and heat number should each be stated on the document.

Metal Bushing (Lubricated Metal) -Self-Lubricating Bushing Materials

Bushings are specialized, self-lubricating metal components widely utilized across various industries due to their durability and low maintenance requirements. Self-lubricating metal bushings are engineered to function without additional lubrication in numerous applications, thereby minimizing maintenance needs. These bushings are available in various series and configurations, such as flanged bushings and split bearings, to meet specific application requirements.

Metal-Polymer Anti-Friction Plain Bearings

Metal-Polymer Composite Self-lubricating Bushing Material

Steel Back + Porous Bronze Sinter + PTFE

Metal-Polymer Plain Bearings Grease Lubricated
Metal-Polymer Plain Bearings Grease Lubricated
Bronze Bearings made of CuSn8 with Lubrication Indents
Bronze Bearings and Bronze Sleeve Bushings made of CuSn8 with Lubrication Indents
Cast Bronze Bushings with Solid Lubricant Inserts
Cast Bronze Bearings with Solid Lubricant Inserts
Bimetal Plain Bearings
Steel + CuPb10Sn10 with indents
Steel Bronze Bushing
Steel Backing and Bronze Overlay
Compare prices and delivery times, then place your order directly online or request a quotation.

lubrication-free Bearing bushing products

Self-lubricating Bushing For High Performance And Low Maintenance