Bronze Bushing Wrapped bronze bushing
Bronze Bushing Selection Guide for Mining and Drilling Equipment

Mining drill rig bushings · application and material guide

Bronze Bushings for Surface DTH Blasthole Drill Rigs

Bushing for drill

Common Applications in Marine Settings

Self-lubricating bearing bushings are increasingly utilized in marine applications due to their unique properties that enhance performance and reduce maintenance needs. These bushings are designed to operate without the need for external lubrication, making them particularly advantageous in environments where traditional lubrication methods are impractical or impossible.

Self-lubricating bearing bushings

Mining drill rig bushings · application and material guide

Bronze Bushings for Surface DTH Blasthole Drill Rigs

A position-by-position application map for crawler-mounted down-the-hole blasthole drill rigs in the 16–26 t class: what each joint demands in service, how to choose between wrapped and solid bronze, aluminium bronze and graphite-plugged self-lubricating variants, and the bore-size and PV limits that decide whether a position can take a plain bushing at all.

Category: mining equipment plain bearings · Typical sizes: bore Ø40–150 mm · Duty: dry dust, impact, slow oscillation · Bore Ø240 mm class pivots covered in section 8

Scope of this guide

This page covers plain and wrapped bushings and sliding elements on surface down-the-hole (DTH) rotary percussion blasthole drill rigs — the crawler-mounted production rigs used in open-pit mining, quarrying and construction aggregate work.

It does not cover: downhole hammer tooling, gearbox and engine bearings, hydraulic cylinder internal parts, or the exploration and underground classes of rig, except where a joint design is explicitly shared between classes. It contains no performance commitment for any specific machine. Bore sizes, tolerances and materials must be confirmed against the machine’s own parts documentation and the measured worn part before ordering.

1 · What this machine class is, and why its bushings are different

A surface DTH blasthole rig is a crawler carrier with a boom, a feed beam that slides or tilts, a rotation head that turns a string of pipes, and a flushing air system that blows cuttings out of the hole. It is not an excavator and not a truck. That matters for bushing selection in three specific ways.

  • The pivots oscillate, they do not rotate. Most bushing positions on this class of rig move through a small angle, a few hundred times a shift. Rotary motion that would drive a PV limit on a continuously rotating shaft never accumulates here, so plain bronze is viable where a rolling bearing would be destroyed by impact.
  • Shock dominates load. The feed beam, boom foot and track frame see peak loads from drilling reaction and from travelling over broken ground. A bushing chosen on static load alone will be under-specified.
  • Dust and grit, not load, cause most failures. Dry rock cuttings are highly abrasive. Sealing, grease retention and surface hardness decide life more often than crush strength does.

Rigs used in wet or coastal quarries shift the balance: there, corrosion resistance moves up the priority list, and aluminium bronze becomes a stronger candidate at the track module and water handling positions.

2 · Machine class benchmarks

Two weight classes dominate this segment. The figures below are class-level ranges published in manufacturers’ specification sheets; treat them as indicative and confirm against the machine’s own data plate.

Table 1 · Class-level benchmarks for surface DTH blasthole drill rigs. Basis: published specification sheets. Indicative, not a specification.
Parameter 16–19 t class (light) 23–26 t class (heavy)
Drilling method DTH rotary percussion, surface DTH rotary percussion, surface
Hole diameter 90 – 229 mm 90 – 203 mm
DTH hammer size 4″ – 7″ 4″ – 6″
Pipe / rod diameter 76 – 114 mm; pipes up to 8 m 76 – 140 mm
Maximum hole depth approx. 50 – 56 m approx. 50 – 54 m
Operating weight approx. 16 – 19 t approx. 23.7 – 25.1 t
Engine power approx. 330 – 400 kW approx. 400 kW
Flushing air approx. 470 l/s 24 – 28 m³/min at 24 – 30 bar
Boom type Articulated or fixed boom with feed beam tilt and rotation Fixed boom with feed beam tilt; fewer joints than an excavator
Documented module structure Feed boom / drilling module / carrier / track module Rotary head · drilling module · boom · carrier · track module · covers · cabin · options
Centralised lubrication Fitted on many units; optional on others Listed as an option — confirm per machine

Design consequence: because the boom is fixed rather than articulated on the heavier class, there are fewer boom joints but more wear concentrated in the feed beam, rotation head slide and rod handling group. When you survey a fleet, count positions by module rather than assuming the boom carries most of the bushings.

3 · Bushing position map on a surface DTH blasthole drill rig

The drawing below is a generic schematic of the class, not a specific machine. Numbered badges correspond to the row numbers in the application matrix in section 4.

track moduleboomfeed beamrotation headdust collector123456789101112
Figure 1 · Bushing positions on a crawler-mounted surface DTH blasthole rig (schematic, not to scale). Badge numbers match the matrix row numbers in Table 2.

4 · Bushing application matrix: position, duty and material

The matrix is grouped the way a parts manual groups the machine — boom, drilling module, track module, carrier and options — so that a survey of one machine maps straight onto the other.

Table 2 · Application matrix for plain and wrapped bushings on surface DTH blasthole drill rigs. 20 positions across five module groups. Material recommendations are starting points for evaluation, not specifications.
# Module Position Duty (motion · load · environment) Recommended type Material Control point
BOOM AND FEED BOOM
1 Boom Boom foot pin Oscillating, small angle · high radial + shock · dust Thick-wall machined bushing or flanged wrapped bushing CuSn8 wrapped or CuAl10Ni5Fe4 The highest shock position on the rig. Select on peak load, not static load. Confirm pin diameter from the boom drawing.
2 Boom Boom lift cylinder eyes (base and rod end) Oscillating · heavy radial · dust Flanged wrapped bushing or plain wrapped CuSn8 wrapped Both eyes wear. Ream and replace as a pair, and check eye concentricity before fitting.
3 Boom Feed beam tilt pivot / feed boom pivot Oscillating · heavy radial · dust and grit Wrapped bushing, plain or flanged CuSn8 wrapped The main feed-boom wear position. Regreasing interval is the life driver; fit dust seals where the joint geometry allows.
DRILLING MODULE — feed beam, rotation head, rod handling
4 Drilling module Feed extension cylinder eye Oscillating, short stroke · heavy radial · dust Flanged wrapped bushing CuSn8 wrapped The cylinder rod is large in diameter while the eye pin is smaller — confirm both from the cylinder drawing.
5 Drilling module Rotation head slide / guide pads Reciprocating slide · medium-high · rock dust and grit Slide pads and sliding pieces, not a rotating bushing Bronze slide pad, composite or graphite-plugged Sliding duty with hard-to-reach lubrication. Wear here shows up as feed misalignment and hole deviation.
6 Drilling module Rod centraliser / guide bushing Sliding plus pipe rotation · medium · heavy rock dust Replaceable insert or die Wear-resistant bronze or polymer insert Consumable by design. It protects the threaded pipe, so its economic life is set by pipe cost rather than by part price.
7 Drilling module Rod changer / carousel arm pivot Oscillating plus indexing · medium · dust Wrapped bushing, plain or flanged CuSn8 wrapped Positioning accuracy drives coupling success; hold the upper clearance limit tight.
13 Drilling module Feed chain tensioner sprocket and guide idler Slow rotation · medium · heavy abrasive dust Bushed sprocket or idler; bushing plus pin CuSn8 wrapped or hardened steel bushing Chain tension setting drives the wear rate. Over-tensioning wears both sprocket and bushing.
14 Drilling module Breakout jaw / clamp pivot and jaw die seat Oscillating with high breakout torque · dust Bushing at the pivot; hardened die at the jaw CuSn8 bushing; tool steel die The die is a hardened wear part, not a bushing. Do not substitute bronze for the die.
15 Drilling module Rotation head mounting and gearbox slide adjustment Static location plus sliding adjustment · heavy · grit Slide plates and adjusting shims Bronze slide plates Adjustment, not wear replacement. Re-shim rather than re-machine.
16 Drilling module Hammer / drive sub bushing at the rotary head Rotation plus shock · high · flushing air carrying rock cuttings Machined bronze bushing Cast tin bronze CuSn10 / CuSn12, or CuAl10Ni5Fe4 Sealing is critical: air-borne cuttings destroy the fit far faster than load does.
17 Drilling module Rod wipe / dust skirt guide rings Sliding · light · heavy dust Elastomer component, not a metal bushing Polyurethane or rubber Listed for completeness. Keep out of a metal bushing quotation to avoid mismatched expectations.
TRACK MODULE
8 Track module Track frame pivot / oscillation bearing Oscillating ±5–8° · very heavy plus shock · abrasive dust and mud Thick-wall bushing, or wrapped bushing with seals CuSn8 wrapped; CuAl10Ni5Fe4 for severe shock Carries full machine weight with impact. Sealing against grit is the single largest life factor.
9 Track module Track tensioner and idler wheel support Slow rotation · medium to heavy · heavy abrasion Bushing and pin set; bushed idler CuSn8 wrapped or hardened steel bushing Track tension setting and seal condition decide life. Check the support bore for ovality at rebuild.
10 Track module Load roller and carrier roller journals Continuous slow rotation · medium · total immersion in grit Bushed roller, sealed Bronze bushing in a sealed roller High-consumption wear item. Grease loss through a failed seal is the usual cause of failure.
CARRIER, COVERS AND OPTIONS
11 Carrier Outrigger / jack leg pivot optional fit Oscillating · medium · dust Flanged wrapped bushing CuSn8 wrapped Fitted as an option on some machines — confirm whether the unit has it before quoting.
12 Covers / dust system Dust collector hood and ducting pivot Oscillating, intermittent · light · extreme dust Plain wrapped bushing or composite CuSn8 wrapped or composite self-lubricating Light duty. Grease escaping into the dust stream is undesirable, so prefer a sealed or plugged design.
18 Carrier Cab and engine hood lift cylinder pivots Oscillating, occasional · light to medium · dust Plain wrapped bushing CuSn8 wrapped Low duty. A standard wrapped bushing is adequate.
19 Carrier Compressor and pump drive coupling bearings Continuous rotation · medium-high · oil splash Anti-friction bearing, not a wrapped bushing Rolling element bearing Distinguish rolling bearings from plain bushings in the quotation; they are different supply lines.
20 Options Water swivel / flushing head pivot water injection option Rotation · medium · water and grit Machined bronze bushing with seal CuSn8 or CuAl10Ni5Fe4 Wet duty. Corrosion resistance matters more here than at any other position on the rig.

Reading the matrix correctly. A row states where a bushing sits, not which part to order. On this machine class, most positions carry no publicly published part number — that is normal for structural joints on low-volume mining equipment. Geometry must be captured from the worn part, from a drawing, or by measurement on the machine. Never quote a size for these positions from a general guide.

5 · Duty profile and material recommendation by position group

Table 3 · Material selection by dominant duty. “First choice” assumes grease lubrication and a serviceable housing.
Position group Dominant duty First choice Alternative
Boom foot and cylinder eyes (1, 2, 3, 4) Slow oscillation, high radial load, shock, dry dust CuSn8 wrapped bushing, plain or flanged CuAl10Ni5Fe4 aluminium bronze where shock is severe or the housing is already worn
Feed beam pivot (3) Oscillation with grit ingress; regreasing often neglected CuSn8 wrapped with dust seals Graphite-plugged bronze where no centralised lubrication is fitted
Slide and guide positions (5, 15) Reciprocating sliding, abrasion, poor lubrication access Bronze slide plates or graphite-plugged pads Composite self-lubricating pads
Rod centraliser (6) and breakout jaw (14) High abrasion against pipe and threads; sacrificial by design Hardened insert or die as originally specified Do not substitute a general bushing bronze — hardness is the function
Rotary head and hammer bushing (16) Rotation plus shock; air-borne cuttings Cast tin bronze CuSn10 / CuSn12 machined bushing CuAl10Ni5Fe4 in abrasive or wet conditions
Track module (8, 9, 10) Full machine weight, shock, continuous grit and mud Sealed bushed roller, or wrapped bushing with seals Hardened steel bushing and pin set where the bore is already damaged
Light-duty pivots (11, 12, 18, 20) Intermittent oscillation, light load CuSn8 plain wrapped bushing Composite where grease must be kept out of a dust stream

6 · Material options for drill rig bushings

6.1 CuSn8 wrapped bronze (CW453K / 2.1030 / C52100)

A cold-rolled phosphor bronze strip formed into a split cylindrical shell. Thin-wall (2.5 mm is a common wall for bores of 50 mm and above), light, and inexpensive per unit. It resists shock well because the thin wall deforms with the housing instead of cracking, and it tolerates dry dust and general atmospheric and water exposure. The temper of the strip — commonly R450 or R540 — sets the strength and hardness band, so it must be specified on the drawing; otherwise the same nominal designation can deliver a load capability that differs by close to a factor of two.

Table 4 · CuSn8 wrapped bushing — representative data. Basis: standard (EN CW453K composition) and typical (manufacturer-published property bands). Indicative values for evaluation.
Property Value Basis
Composition (wt%) Cu balance · Sn 7.5–8.5 · P 0.01–0.40 · Zn ≤0.20 · Fe ≤0.10 · Ni ≤0.20 · Pb ≤0.02 Standard
Density 8.8 g/cm³ Typical
Tensile strength Rm 370 – 630 MPa (temper dependent) Typical
Yield strength Rp0.2 250 – 460 MPa Typical
Hardness 90 – 200 HV Typical
Elongation A 13 – 50 % Typical
Allowable static load 120 N/mm² Typical (grease)
Allowable dynamic load 40 N/mm² Typical (grease)
Allowable sliding speed v 2.5 m/s Typical (grease)
Allowable PV 2.8 N/mm²·m/s Typical (grease) — the governing limit for large bores
Friction coefficient, lubricated 0.05 – 0.25 Typical
Operating temperature −40 … +200 °C (practical limit set by the grease) Typical — confirm grease rating
Housing tolerance H7; verify bore to H9 after fitting Practice (ISO 3547 / DIN 1494 family)
Shaft tolerance f7 – f8 preferred for oscillating pivots Practice
Shaft roughness Ra ≤ 0.8 µm; may relax to 1.6 µm on hardened shafts Practice
Shaft hardness ≥ 200 HB as a starting point Practice — set from the measured pin, see section 11

6.2 Cast tin bronze (CuSn10 / CuSn12 class)

Continuous-cast or centrifugally cast, then machined to size. Higher load capacity than a thin-wall wrapped shell and able to be re-bored in the field, which makes it the practical answer for bores above roughly 150 mm, for housings that are already worn, and for the rotary head position where rotation and shock combine. The trade-off is mass and unit cost, and it requires a real lubrication path — a cast bronze bushing run dry in an inaccessible position will score the pin.

6.3 Aluminium bronze (CuAl10Ni5Fe4 class)

Markedly higher strength and hardness than tin bronze, with the corrosion resistance needed for wet, coastal and acidic water service. It is the alternative at the boom foot, track frame pivot and water swivel positions where shock is severe or corrosion is present. It is harder on the counterface, so pin hardness and surface finish need to be verified at the same time — an aluminium bronze bushing on a soft, rough pin will wear the pin instead.

6.4 Graphite-plugged self-lubricating bronze

A cast bronze body with graphite plugs set into the sliding surface, providing a solid lubricant film without an external grease supply. This is the appropriate choice for positions where the greasing route is blocked, where grease escaping into a dust stream is unacceptable, or where the machine carries no centralised lubrication system. It runs a higher friction coefficient than a grease-lubricated bushing, so it suits oscillation and light rotation rather than continuous high-load rotation.

6.5 Composite and polymer inserts

Used for the rod centraliser and guide positions where the function is to protect a threaded pipe or a chromed rod rather than to carry structure. These are sacrificial by design and should be costed as consumables, in a separate supply line from structural bushings.

6.6 When a hardened steel bushing or a rolling bearing is the correct answer

Track tensioner supports, sprocket idlers and drive couplings appear in the same parts groups as bronze bushings but are not interchangeable with them. Where the bore is already damaged, where the duty is genuine continuous rotation, or where the original design uses a rolling element bearing, substituting bronze produces a repeat failure. Keep the supply lines separate in the quotation.

7 · Bushing construction types compared

Table 5 · Construction type comparison for drill rig joints.
Type Where it fits Advantages Limits
Wrapped (seamed) shell, plain Boom, cylinder eyes, light pivots; bore 20–150 mm Thin wall saves space; low mass; low unit cost; tolerant of shock Cannot be re-bored; housing roundness matters; axial location needs a shoulder or a circlip
Wrapped shell with flange Pivots needing axial location without a separate thrust face Integrates axial location; simpler assembly Flange is a location feature only — it is not a thrust bearing; flange thickness is limited by strip thickness
Machined solid bronze Large bores, worn housings, rotary head, high shock High load capacity; can be re-bored; can carry lubrication grooves Higher mass and cost; needs a real lubrication path
Graphite-plugged bronze Blocked lubrication routes, dust-sensitive positions No external grease supply needed Higher friction; graphite plugs are a wear surface to monitor
Bimetal (steel-backed) High-load pivots with thin available wall Steel backing gives high crush resistance in a thin section Requires a sound, round housing; corrosion protection of the backing matters in wet service
Slide pad / sliding piece Rotation head slide, feed beam guides Rectangular geometry carries load over a wide face Not a rotating bushing — do not substitute; wears by sliding abrasion
Replaceable insert / die Rod centraliser, breakout jaw Protects the expensive counterface; quick to change Hardness is the function; general bushing bronze is not a substitute

8 · Bore size classes found on this machine class

Before any material discussion, check that the bore size belongs to the machine. Surface DTH blasthole rigs in the 16–26 t class use pins and journals in a fairly narrow band. Anything far outside that band is probably a different class of machine — a large rotary blasthole drill, a rope shovel, a dragline, or a mill and crusher application — and should be confirmed before technical work continues.

Table 6 · Typical bore sizes on surface DTH blasthole drill rigs, by position family.
Position family Typical pin / bore Ø Note
Linkage pins and matching bushings 40 – 60 mm The sizes most commonly documented with a published dimension on this class
Feeder rotation and tilt cylinder eyes 50 – 80 mm Cylinder rod diameter is usually larger than the eye pin
Boom lift and feed extension cylinder eyes 80 – 90 mm Rod diameter in this band on the heavier class
Boom foot, feed beam pivot, track frame pivot 90 – 150 mm Structural joints; the largest plain bushings on the machine
Rotary head output shaft seals 125 – 150 mm Upper end of the documented journals on this class
Outside the class 200 mm and above Not found on a 16–26 t surface DTH rig. Confirm the target machine before quoting.

Sizing sanity check. A bore of Ø240 mm is roughly 1.6 times the largest journal and about six times the smallest linkage pin documented on this machine class. If an enquiry arrives with a bore in that range, the first clarifying question is which machine it belongs to — not which material. Quoting a large-bore mill or shovel bushing against a drill rig enquiry puts an unusable part in front of the customer.

9 · Speed and PV limits: why large-bore pivots cannot rotate

An allowable PV of 2.8 N/mm²·m/s is a product constraint, which means that as bore diameter grows, the permitted speed falls. Using v = π·d·n / 60000 with d in mm and n in r/min, and a specific load of 40 N/mm² (the typical allowable dynamic load for a grease-lubricated wrapped bronze bushing):

Table 7 · Permitted speed at an allowable PV of 2.8 N/mm²·m/s and a specific load of 40 N/mm². Basis: typical allowable values; verify against the selected material and lubrication.
Bore d (mm) Permitted v (m/s) Permitted n (r/min) Relevance to this machine class
40 0.070 33.4 Documented linkage pin size. Pivot duty sits far below this.
60 0.070 22.3 Typical cylinder eye pin.
90 0.070 14.9 Cylinder rod band; boom and track pivots sit near this class.
120 0.070 11.1 Large structural pivot. Rotation begins to be impractical.
150 0.070 8.9 Upper end of the documented journals on this class.
240 0.070 5.6 Large-bore pivot. Oscillating duty only — outside this machine class.

For the same reason, load and speed trade off directly. At a bore of 240 mm and a bushing length of 90 mm the projected area is 21 600 mm², so:

Table 8 · Load and speed trade-off for a 240 × 90 mm plain bushing, projected area 21 600 mm². Basis: calculated from typical allowable values.
Specific load p (N/mm²) Corresponding radial load (kN) Allowable v (m/s) Allowable n (r/min) Application verdict
40 864 0.070 5.6 Oscillating pivot, intermittent motion
25 540 0.112 8.9 Slow oscillation, luffing
10 216 0.280 22.3 Low-speed rotation may be considered
5 108 0.560 44.6 Light-duty rotation

Conclusion. Large-bore plain bushings belong on pivot joints with oscillating motion. If a large-bore position is expected to rotate continuously, the design must be re-evaluated with a thick-wall cast tin bronze, an aluminium bronze, or a steel-backed bimetal bushing — and above roughly ten r/min on a large bore, the PV budget usually forces a different bearing type altogether.

10 · Failure modes and how to read them

Table 9 · Failure modes of drill rig bushings and their usual root cause. Based on field failure patterns in dry, abrasive service.
Observed failure Usual root cause Corrective action
Uniform wear, bore out of tolerance, pin polished Normal service life reached Replace bushing and pin as a pair; measure the housing before fitting
Heavy one-sided or oval wear Misalignment, bent pin, or an out-of-round housing Check housing roundness and pin straightness — a new bushing will repeat the failure
Seizure, galling, torn surface Loss of lubrication, or a counterface harder and rougher than specified Restore the lubrication route; measure pin hardness and Ra; consider a graphite-plugged variant
Bushing rotated or walked in the housing Insufficient interference fit, housing oversize, or axial location missing Re-sleeve or re-machine the housing; add a shoulder or circlip
Flange cracked or deformed Concealed thrust load taken through a location flange Add a proper thrust face or washer; do not use the flange as a thrust bearing
Crevice corrosion, verdigris, pitting Water ingress, acidic water, or a coastal environment Move to aluminium bronze at the affected positions; improve sealing
Cuttings embedded in the bearing surface Failed seal, missing dust cover, or flushing air carrying grit into the joint Restore sealing before replacing the bushing; supply the seal with the bushing
Wear concentrated in the first 20 % of life Fitting damage — pressed in with a hammer, or over a sharp-edged bore Use a guided mandrel and press; chamfer the housing entry; check the bore after fitting

On this machine class, grit and mud ingress accounts for the majority of premature failures, not load. A bushing supplied without the associated seal and a defined regreasing interval is a repeat failure in the making.

11 · Specification, installation and storage notes

11.1 Tolerances and fits

  • Housing: H7 is standard practice. Large thin-wall wrapped bushings compress when pressed; if the bore matters, verify it to H9 after fitting, not before.
  • Shaft: f7 to f8 for oscillating pivots. A tighter fit is not automatically better — it reduces the clearance needed to carry the grease film.
  • Surface finish: Ra ≤ 0.8 µm is the usual requirement; 1.6 µm may be acceptable on hardened shafts.
  • Shaft hardness: published requirements differ widely across sources — from ≥ 200 HB to ≥ 45–55 HRC depending on the product family. This must be set from the measured hardness of the actual pin, not from a catalogue figure. Specifying the low end and then shipping into an application designed for the high end is a common and expensive error.

11.2 Fitting

  • Clean and deburr the housing; chamfer the bore entry so the seam cannot catch.
  • Press with a guided mandrel sized to the bushing outer diameter — never through the bore, and never with a hammer.
  • Align the seam away from the load direction where the design permits.
  • Do not re-machine a thin-wall wrapped bushing after fitting; if the fit is wrong, the part is scrap.
  • Supply fitting instructions in the customer’s language where the workshop is not English-speaking.

11.3 Grease and seals

  • Confirm whether the machine carries a centralised lubrication system and how often the position is actually greased in practice. Most positions are under-greased, not under-specified.
  • Specify the grease and the interval with the bushing. On dust-exposed positions, the seal is part of the bearing.
  • Prefer a sealed or graphite-plugged design where grease escaping into a dust stream or onto a pipe thread is unacceptable.

11.4 Storage

  • Store wrapped bushings flat and protected from impact; a thin-wall shell is easily distorted out of round before fitting.
  • Keep sealed and lubricated parts in their packaging until use. Open storage in a quarry environment contaminates them before they are installed.

12 · Specification checklist for a drill rig bushing enquiry

Print and complete this with the customer or the workshop. Every line changes the part that leaves the warehouse.

  • Machine identity: model, series and serial number, so the position can be located in the correct parts documentation.
  • Position: module and position name, a marked photograph, or the parts manual page and item number.
  • Geometry: bore, outer diameter, length, flange diameter and flange thickness — measured from the worn part or taken from the drawing.
  • Construction: is the original a thin-wall wrapped bushing, a machined solid bronze bushing, a steel-backed bimetal bushing, or a bushed roller?
  • Counterface: pin diameter and measured hardness, and whether the pin is re-used or replaced at the same time.
  • Housing: bore tolerance and roundness, and whether the housing is serviceable or needs sleeving.
  • Motion and load: oscillating or rotating, angle or speed, static load and expected peak shock load.
  • Lubrication: is a centralised system fitted, how often is the position greased, and is grease starvation the reason for the current failure?
  • Environment: dry dust, wet, coastal, or acidic water — this decides whether aluminium bronze is required.
  • Failure history: how many hours did the last part give, and how did it fail — wear, seizure, collapse, corrosion, or a lost seal?
  • Volumes: quantity per machine, machines of this model in the fleet, and annual consumption per position.
  • Documentation: material certificate, dimensional inspection report and bilingual fitting instructions required?

13 · Frequently asked questions

Which bronze is used for drill rig bushings?

Wrapped CuSn8 phosphor bronze covers most oscillating pivot positions on a surface drill rig, because it is thin-walled, light and tolerant of shock. Cast tin bronze in the CuSn10–CuSn12 range is used where the bore is large, the housing is worn, or rotation combines with shock, as at the rotary head. Aluminium bronze in the CuAl10Ni5Fe4 class is chosen where shock is severe or where the machine works in wet, coastal or acidic water.

Why do drill rig bushings often have a flange?

The flange locates the bushing axially in the joint and simplifies assembly. It is not a thrust bearing. On a thin-wall wrapped bushing the flange thickness is set by the strip thickness, so its axial load capacity is limited by plate bending. A joint with concealed thrust load needs a separate thrust face or washer.

Can a bronze bushing run without grease on a drill rig?

Only if it is a self-lubricating design — typically cast bronze with graphite plugs set into the sliding surface. These are used where the greasing route is blocked, where grease escaping into a dust stream is a problem, or where the machine has no centralised lubrication system. They run a higher friction coefficient than grease-lubricated bushings and suit oscillation and light rotation rather than continuous high-load rotation.

How do I check whether a bushing size belongs to a surface drill rig?

Compare it against the class. Surface DTH blasthole rigs in the 16–26 t range use pins and journals from roughly Ø40 mm at linkage pins and cylinder eyes up to Ø150 mm at the largest structural pivots. A bore of 200 mm or above does not belong to this class and most likely indicates a large rotary blasthole drill, a rope shovel, a dragline, or a mill and crusher application.

What causes most premature bushing failures on mining drill rigs?

Abrasive dust and mud ingress rather than overload. Dry rock cuttings embed in the bearing surface and grind the fit away, and the failure is usually traceable to a perished seal, a missing dust cover, or a greasing interval that is not met in practice. On the track module and the feed beam pivot, checking the seal is more productive than changing the material.

How is bushing life predicted on an oscillating pivot?

On oscillating duty the PV limit is rarely the binding constraint because the sliding distance per cycle is small. Life is driven instead by the number of cycles, the peak shock load, the counterface hardness and roughness, and how well grit is excluded. That is why the same bushing can last very differently across two machines of the same model — the maintenance regime, not the catalogue rating, is the variable.

14 · Scope-limit declaration

This guide is an engineering selection aid for industrial plain bearings. It contains no conclusion, approval or certification in any of the following domains, and nothing on this page may be relied on as one:

Table 10 · Sector boundary. Standards and regulators are cited by document number only; no approval or certification is claimed or implied in any sector.
Sector Applicable regime (cited by number only) What this guide does not provide
Aerospace EASA / FAA Part 21, AS9100, NADCAP No airworthiness finding and no certification basis of any kind
Defence ITAR 22 CFR 120–130, EAR 15 CFR 730–774 No defence qualification, no export classification, no military specification conformance
Automotive IATF 16949 No automotive product approval; IATF 16949 is an organisation-level quality system requirement, not a product approval
Food contact EC 1935/2004, EU 10/2011, 21 CFR 177.1550 No food contact compliance statement; 21 CFR 177.1550 covers resin, not copper alloy bushings
Medical devices EU MDR 2017/745, FDA device requirements No medical device approval or classification
Nuclear ASME NQA-1, RCC-M No nuclear quality assurance qualification
Explosive atmospheres ATEX 2014/34/EU, EN ISO 80079-36 / -37 The equipment described here is not assessed for explosive atmospheres; no category, equipment protection level or temperature class is assigned

Material property data presented here is provided as a data source for engineering evaluation only and does not constitute an airworthiness finding, a certification basis, or any other certification conclusion.

15 · Appendix: terminology, units and data basis

15.1 Terminology conventions

Term as used here Meaning in this guide
Wrapped bushing A plain bearing formed from rolled strip into a split (seamed) cylindrical shell, also described as a seamed or rolled bushing. Referred to in the ISO 3547 and DIN 1494 standard families.
Oscillating duty Reciprocating motion through a limited angle, with no continuous rotation; the controlling wear mechanism is boundary lubrication under repeated reversal.
Blocked lubrication route A position that is physically inaccessible for routine greasing, or that is documented but not actually serviced in the field.
Projected area Bore diameter multiplied by bushing length; the area over which specific load p is calculated.
Class A weight and capability band of machines, not a specific model or serial number.

15.2 Units and conversions

  • Specific load p: N/mm² (1 N/mm² = 1 MPa).
  • Sliding speed v: m/s. Speed in r/min from bore: n = 60000·v / (π·d) with d in mm.
  • PV: N/mm²·m/s. The product limit, not either term alone, governs large-bore positions.
  • Surface roughness: Ra in µm. Ra 0.8 µm ≈ 32 µin.

15.3 Data basis and known divergences

  • Standard vs typical: composition rows marked Standard reflect a published standard requirement. Rows marked Typical are values published by manufacturers or found consistently in practice, and are indicative figures rather than minimum values. The two are never merged on this page.
  • Mechanical properties are temper dependent. The cold-worked temper of the strip changes tensile strength and hardness substantially across the same nominal designation. Any strength figure quoted without a temper is incomplete.
  • Shaft hardness requirements conflict between sources. Published values range from ≥ 200 HB to ≥ 45–55 HRC for the same nominal product family. This guide does not average them. The requirement must be set from the measured hardness of the actual pin, and the higher value should be screened against where the consequence of failure is severe.
  • Allowable values are conditional. The allowable load, speed and PV figures depend on lubrication mode, clearance, surface finish and counterface condition. They are published for evaluation and are not a performance commitment.
  • Machine class figures are indicative. Hole diameter, weight, engine power and rod diameters are class-level ranges from published specification sheets and vary by build and option.

Plain Bushings Industry

Plain bearing bushings are widely used across various industries for their durability, self-lubricating properties, and cost-effectiveness. When creating custom-sized orders for industries like Marine, Hoist Bearings, Oil & Gas, and Hydraulic Equipment, several considerations should be kept in mind, such as material selection, load capacity, environmental factors, and specific requirements for maintenance or lubrication. Self-lubricating plain bearings and bushings with a sintered sliding layer are ideal for continuous operation in demanding environments, offering reliable, high-performance, grease-free solutions.

Marine
Hoist Bearings
Oil & Gas Industry
Hydraulic Equipment
Mining & Construction
Forklifts & Trucks
Tire & Rubber
Agriculture